TechniSat DigiCorder S1 Manual de usuario Pagina 52
- Pagina / 78
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
8.4.2 Satellite scan
UTo scan a specific satellite for programmes, select the
option Satellite scan (Fig. 8-16). You can select whether you
wish to scan for all programmes (free-to-air and encrypted) or
only for free-to-air programmes.
> Press the OK key again to open the selection table of
active satelites.
> Use the up/down arrow keys to mark the line All
satellites to scan all active satellites for programmes,
or mark the desired satellite to scan only this for pro-
grammes.
> Confirm by pressing OK.
> Use the up/down arrow keys to mark the field Scan
mode.
> Use the OK key to select whether you wish to scan
only for free-to-air programmes (Free programmes) or
whether you wish to include encrypted programmes
(All programmes).
> Press the red function key Start scan.
The scan will be started. Please note an y messages
displayed on screen.
>You can stop the scan at any time by pressing the red
function key.
8.4.3 Transponder scan
You may scan a specific transponder (see Point 10 Technical
terms) for programmes. To do this, you will have to enter the
transponder data (Fig. 8-17).
Satellite
In this line, select the satellite on which the desired transpon-
der is located.
> Use the up/down arrow keys to mark the line
Satellite.
> Press OK to display a table showing the active satelli-
tes.
> Now use the up/down arrow keys to mark the des-
ired satellite.
> Confirm by pressing OK.
The selected satellite will now be indicated in the line
Satellite.
Transponder frequency
> Use the up/down arrow keys to mark the line
Transponder frequency.
> In this line, use the numeric keys to enter the appro-
priate frequency.
Symbol rate
The symbol rate indicates the volume of data transmitted per
second. A typical figure might be, for example, 27500 (27500
52
(Fig. 8-17)
(Fig. 8-16)
Bed_Anl_Digicorder_englisch 18.03.2004 14:10 Uhr Seite 52
- DigiCorder S1 1
- 1 Contents 2
- 2 Illustrations 5
- 3 Please read this first 8
- Disposal information 9
- Safety notes 9
- Temporary disconnection 9
- 4 Connections 11
- 4.3.2 Via HF cable 12
- 4.5 HiFi Amplifier 12
- 4.5.1 Analogue 12
- 4.5.2 Digital 13
- 4.7 Serial Interface (RS 232) 13
- 5 Initial installation 13
- (Fig. 5-6) 14
- (Fig. 5-7) 14
- (Fig. 5-3) 14
- (Fig. 5-4) 14
- (Fig. 5-5) 14
- (Fig. 5-8) 15
- (Fig. 5-9) 15
- (Fig. 5-10) 15
- (Fig. 5-11) 15
- (Fig. 5-12) 15
- 6 Settings 16
- 6.2 Basic settings 17
- 6.2.2 Country 17
- 6.2.3 Remote control code 17
- 6.2.4 Standby clock 17
- 6.3 Audio/Video settings 18
- 6.3.1 Picture format TV set 18
- 6.3.2 Language (Audio signal) 18
- 6.3.3 Language (Sub-titles) 18
- 6.3.4 TV SCART mode 18
- 6.3.5 Video system 19
- 6.3.6 Dolby Digital (AC3) 19
- 6.3.7 UHF output channel 19
- 6.4 Antenna settings 20
- Example: 21
- 7 Operation 22
- 7.2 Programme selection 23
- 7.2.2 Using the numeric keys 23
- 7.2.3.1 Selecting a list 23
- 7.2.5 Information box 24
- Special functions 25
- 7.3.1 Multifeed options 25
- 7.4 Volume control 26
- 7.6 TV/Radio switching 27
- VT group VT block 28
- 7.13 Sub-titles 29
- (SiehFern Info) 29
- 7.14.1 Downloading SFI data 30
- 7.14.5 Next 31
- 7.14.6 More 31
- 7.14.7 SFI functions 32
- 7.14.7.1 SFI Info 32
- (Fig. 7-19) 33
- (Fig. 7-20) 33
- 7.14.8 Exiting from SFI 34
- 7.15 Hard drive operation 34
- 7.15.1 Recording 34
- 7.15.1.1 Instant recording 35
- 7.15.1.2 Timer recordings 36
- Manual timer programming 37
- Timer overview 38
- Changing timer programming 38
- Deleting timer programming 39
- Programming a new timer event 39
- Timeshift function 39
- 7.15.2 Play 40
- 7.15.2.2 Pause/Freeze frame 41
- 7.15.2.4 Ending Play 41
- 7.15.3.1 Managing recordings 42
- 8 Changing basic programming 43
- (Fig. 8-3) 44
- (Fig. 8-1) 44
- (Fig. 8-2) 44
- 8.1.3 Deleting programmes 45
- 8.1.4 Sorting programmes 46
- 8.2.1 Selecting a programme 47
- 8.2.2 Start category 48
- 8.2.3 SFI channel 48
- 8.3 Parental control 49
- 8.3.1 Changing the unit PIN 49
- 8.3.2 Mode 50
- 8.3.3 Selecting a programme 50
- 8.4 Programme scan 51
- 8.4.1 Automatic scan 51
- 8.4.2 Satellite scan 52
- 8.4.3 Transponder scan 52
- 8.4.4 Manual scan 53
- 8.4.5 After the scan 53
- 8.5 Service settings 54
- 8.5.2 Delete all programmes 55
- 8.5.3 Updating software 55
- 8.5.4 Copying the settings 56
- 8.6 System configuration 56
- 8.7 Encryption system 56
- (DiSEqC 1.2) 57
- 9.1.2 Set Eastern limit 58
- 9.1.3 Setting Western limit 58
- 9.2 Geo positioning 58
- (User satellite) 60
- (Fig. 9-12) 61
- 9.4 Current satellite list 62
- 10 Technical Terms 63
- 11 Technical data 66
- 12 Troubleshooting guide 69
- 13 Annexu 71
- For everyday operation 76
- 342_03 2233440000800 77
Relacionado con productos y manuales para Decodificadores de tv TechniSat DigiCorder S1
(176 paginas)
Decodificadores de tv TechniSat S1 Manual de usuario
(102 paginas)
(102 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales